Pedders Shock Absorber Service Pty Ltd

PO Box 247

NOBLE PARK VIC 3174

ATTENTION: Mr David Schneiders

 

Dear Mr Schneiders

The application for a Identification Plate Approval, your reference number NAGEN8CA, our reference number 47825, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.

Your approval number is 47825 and the approval documents are attached.

Yours sincerely

 

 

 

 

Associate Administrator of Vehicle Standards

01 June 2016

 

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Regional Development

MOTOR VEHICLE STANDARDS ACT 1989

Section 10A.(2) Approval

Approval No.: 47825

Issue date: 31 May 2016

The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administratorís circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that ruleís distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administratorís Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.
  11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 47825 Issue Date: 31 May 2016

Schedule 1

Pedders Shock Absorber Service Pty Ltd

6 Bridge Road

KEYSBOROUGH

VIC 3173

 

Schedule 2

Make : Pedders Toyota

Model : HiLux GVM PLUS

Category : NA

Manufactured by : Pedders Shock Absorber Service Pty Ltd

Typical VIN : MR0HA3CD500372046

Seating Capacity : 2; 4; 5

GVM : 3.45 tonne TO 3.45 tonne

 

Schedule 3

Expiry date : Life of Model

Plate location : 10 M 20

Plate colour : SILVER

 

 

 

 

 

 

 

Administrator of Vehicle Standards

31 May 2016

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 47825 Issue Date: 31 May 2016

Schedule 4

ADR Document Reference from evidence item

01/00 0100GEN8

02/01 0201GEN8

03/03 0303GEN8

04/05 0405GEN8

05/05 0505GEN8

06/00 0600GEN8

08/01 0801GEN8

10/02 (also satisfying 10/01) 1002GEN8

10/02 1002GEN8

11/00 1100GEN8

13/00 1300GEN8

14/02 1402GEN8

18/03 1803GEN8

23/02 (also satisfying 23/01) 2302GEN8

23/02 2302GEN8

25/02 2502GEN8

29/00 2900GEN8

30/01 3001GEN8

35/05 (also satisfying 31/03) 3505SEGEN8-1 (Minor Non-Compliance, see Schedule 5)

31/35SF 3505SFGEN8

31/35SF 3505SFGEN8-1

35/05 3505SEGEN8-1 (Minor Non-Compliance, see Schedule 5)

42/04 4204GEN8

43/04 4304GEN8

45/01 4501GEN8

46/00 4600GEN8

47/00 4600GEN8

48/00 4800GEN8

49/00 4900GEN8

50/00 5000GEN8

51/00 5100GEN8

61/02 6102GEN8

69/00 6900GEN8

72/00 7200GEN8

76/00 7600GEN8

79/04 (also satisfying 79/03) 7904GEN8

79/04 7904GEN8

81/02 8102GEN8

83/00 8300GEN8

Approval No.: 47825 Issue Date: 31 May 2016

Schedule 5

 

1. This approval is for second-stage-manufacturer Pedders Shock Absorber Service Pty Ltd for the Pedders Toyota HiLux GVM Plus, based on first-stage approval no. 47341 Toyota Hilux 8GEN.

This vehicle does not fully comply with Australian Design Rule 35/05 - Commercial Vehicle Brake Systems. The Brake Assist System has not been re-tested following the second stage of manufacture by Pedders Shock Absorber Service Pty Ltd, as required by required by clause 4.1.1.1 of ADR 35/05.

This non-compliance in considered minor and inconsequential by the Administrator.

2. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:

Niddrie Nameplates Pty Ltd

P.O. Box 106

Niddrie

VIC 3042

Phone: (03) 9335 2977

Facsimile: (03) 9335 4357

3. The 'chassis-cab' variants of the MAKE&MODEL vehicle type do not comply with the position requirements of ADR13/00 for the following lamps and reflectors:

- reversing lamps

- rear direction indicator lamps

- rear reflex reflectors

- rear registration plate lamps

- rear position (side) lamps

- stop lamps

4. The 'chassis-cab' variants of the MAKE&MODEL vehicle type do not comply with:

- clause 14.2 of ADR42/04 for wheel guards on the rearmost wheels.

- clause 9.1.1.1 of ADR61/02 for provision of a rear registration plate.

5. The manufacturer must provide instructions, guidelines and references to the relevant ADRs, that must be met, to whoever is responsible for completing chassis-cab vehicles certified in accordance with Circular 0-4-11 prior to their supply to the market.