Blade Electrical Vehicles Pty Ltd

PO Box 131

HARCOURT VIC 3453

ATTENTION: Mr Ross Blade

 

Dear Mr Blade

The application for a Identification Plate Approval, your reference number 0260309A3, our reference number 41245, lodged for Blade Electrical Vehicles Pty Ltd, has been approved.

Your approval number is 41245 and the approval documents are attached.

Yours sincerely

for Administrator of Vehicle Standards

01 October 2010

 

 

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Transport

MOTOR VEHICLE STANDARDS ACT 1989

Section 10A.(1) Approval

Approval No.: 41245

Issue date: 30 September 2010

The Administrator of Vehicle Standards (the Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.
  11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 41245 Issue Date: 30 September 2010

Schedule 1

Blade Electrical Vehicles Pty Ltd

2 Hitchcock ST

CASTLEMAINE

VIC 3450

 

Schedule 2

Make : BEV HYUNDAI

Model : GETZ ELECTRIC

Category : MA

Manufactured by : Blade Electrical Vehicles Pty Ltd

Typical VIN : KMHBT51DR6U123456

Seating Capacity : 4

 

Schedule 3

Expiry date : Life of Model

Plate location : Left A-pillar below the 1-st manufacturer's plate

Plate colour : SILVER

Steve Pantelidis

Administrator of Vehicle Standards

30 September 2010

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 41245 Issue Date: 30 September 2010

Schedule 4

ADR Document Reference from evidence item

01/00 0260309-01

06/00 0260309-06

08/01 0260309-08

11/00 0260309-11

13/00 0260309-13

14/02 0260309-14

18/03 0260309-18

21/00 0260309-21

23/01 0260309-23A

25/02 0260309-25

31/01 0260309-31

31/35SF 0260309-31F

34/01 0260309-34

42/04 0260309-42

43/04 0260309-43

46/00 0260309-46

47/00 0260309-47

48/00 0260309-48

49/00 0260309-49

50/00 0260309-50

51/00 0260309-51

52/00 0260309-52

60/00 0260309-60

61/02 0260309-61

69/00 0260309-69

69/00 0260309-69A

72/00 0260309-72

73/00 0260309-73

73/00 0260309-73A

82/00 0260309-82

83/00 0260309-83

83/00SF 0260309-83F

Approval No.: 41245 Issue Date: 30 September 2010

Schedule 5

 

 

 

The Licensee to whom this Approval is issued is limited to placing Identification Plates to no more than 100 vehicles within each 12 month period, following the date of issue of the approval, to vehicles within the Category specified in Schedule 2. This vehicle limit applies regardless of the number of Approvals the Licensee may hold.

The Licensee must obtain all Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with -:

Niddrie Nameplates Pty Ltd

P.O.Box 106

Niddrie

VIC 3042

Phone: (03) 9335 2977

Facsimile (03) 9335 4357