Jenkins Springs Pty Ltd
PO Box 398
BASSENDEAN WA 6934
ATTENTION: Mr James
McCully
Dear Mr McCully
The application for a Identification Plate Approval, your reference
number WCSTPCA, our reference number 50666, lodged for Jenkins Springs Pty Ltd, has been approved.
Your approval number is 50666 and
the approval documents are attached.
Yours sincerely
Umesh Shamdasani
Associate
Administrator of Vehicle Standards
05 March 2020
Department of Infrastructure,
transport, Cities and Regional Development
Issue date: 04 March 2020
The
Associate Administrator of Vehicle Standards (the Associate Administrator)
approves the affixing, by the Licensee named and described in Schedule 1 (the
Licensee) to a vehicle of the kind described in Schedule 2 which conforms to
the design as specified in the evidence items listed in Schedule 4 (the
specified vehicle) which the Licensee has certified complies with the
Australian Design Rules specified in Schedule 4, of an Identification Plate of
the colour specified in Schedule 3, that conforms with the Administrator’s
circular 0-3-2, and which contains the information shown in Schedule 2 (with
the typical VIN replaced with the relevant VIN).
In this approval, a reference to an Australian Design
Rule is a reference to a rule cited in the National Standard determinations,
made under section 7 of the Motor Vehicle Standards Act, together with that
rule’s distinguishing number.
The licensee must pay a fee to the
Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2
of the Motor Vehicle Standards Regulations, for the placement of an
identification plate on each new vehicle supplied to the market in Australia in
accordance with the approval. The
administrative arrangements for the payment of fees are set out in
Administrator’s Circular 0-3-2. Where a
condition exists in Schedule 5 of the approval for the licensee to obtain
plates through the Authorised Plate Contractor, this fee is collected as part
of that process.
This approval is subject to the following
conditions.
1. The
Licensee shall not affix the Identification Plate to a vehicle that is not a
specified vehicle.
2. The
Licensee must not place Identification Plates on vehicles which do not comply
with all of the Australian Design Rules specified in Schedule 4.
3. The
Licensee shall not without the prior approval of the Administrator affix the
Identification Plate to a vehicle that is in any way different from the vehicle
described in the final form of the application for this Approval. The application
includes reports and other documents relating to the application.
4. The
Licensee shall by detailed quality control and test ensure continuing
compliance with such of the Australian Design Rules specified in Schedule 4.
5. The
Licensee shall maintain records of detailed quality control and test
documentation.
6. The
Licensee shall supply upon request, to the satisfaction of the Administrator,
any additional information for the purpose of demonstrating compliance with
such of the Australian Design Rules specified in Schedule 4.
7. The
Licensee shall not affix the Identification Plate to a vehicle on or after the
implementation date for a new Australian Design Rule applicable to the
specified vehicle.
8. The
Licensee shall not affix the Identification Plate to a vehicle on or after the
Expiry date specified in Schedule 3 (if any).
9. The
Identification Plate shall be affixed to the vehicle to which it relates in the
position specified as Plate Location in Schedule 3.
10. On
cessation of marketing the specified vehicle in Australia, the Licensee shall
notify the Administrator of the date of manufacture and VIN of the last
specified vehicle supplied to the market in Australia.
11. The
Licensee shall also comply with the additional conditions specified in Schedule
5.
Approval No.: 50666 Issue Date: 04 March 2020
Schedule
1
Jenkins Springs Pty Ltd
188 Railway Parade
BASSENDEAN
WA
6054
Schedule
2
Make :
WCS Toyota
Model :
WCS Prado 150
Category :
MC
Manufactured by :
Jenkins Springs Pty Ltd
Typical VIN :
JTEBR9FJ705123456
Seating Capacity :
5; 7
Schedule
3
Expiry date : Life of Model
Plate location : Front
passenger door sill rear edge of
body-side above first stage
Identification Plate
Plate colour : SILVER
Umesh Shamdasani
Associate
Administrator of Vehicle Standards
04 March 2020
Please note: If
you do not comply with a condition specified in this Approval the Administrator
may, after giving you notice, revoke the Approval.
Approval No.: 50666 Issue Date: 04 March 2020
Schedule
4
ADR Document Reference from evidence item
01/00
SSM0100
02/01
SSM0201
06/00
SSM0600
08/01
SSM0801
11/00
SSM1100
13/00
SSM1300
14/02
SSM1402
18/03
SSM1803
25/02
SSM2502
29/00
SSM2900
30/01
SSM3001
31/35SF
WCSTPSF3506
34/02 (also satisfying 34/01) SSM3402
35/06
WCSTP3506
43/04
WCSTP4304
46/00
SSM4600
77/00 (also satisfying 46/00) SSM7700
47/00
SSM4700
48/00
SSM4800
49/00
SSM4900
50/00
SSM5000
51/00 SSM5100
52/00
SSM5200
60/00
SSM6000
61/02
SSM6102
62/02 SSM6202
69/00
SSM6900
72/00
SSM7200
75/00
SSM7500
76/00
SSM7600
77/00
SSM7700
78/00
SSM7800
79/04
SSM7904
81/02
SSM8102
82/00 SSM8200
83/00
SSM8300
88/00
WCSTP8800
95/00
CIRC0469500b
95/00 CIRC0469600
96/00
CIRC0469600a
Approval No.: 50666 Issue Date: 04 March 2020
Schedule
5
THIS
APPROVAL WILL REMAIN IN FORCE UNTIL THE END OF THE TRANSITIONAL PERIOD AS
DEFINED IN THE ROAD VEHICLE STANDARDS (CONSEQUENTIAL AND TRANSITIONAL
PROVISIONS) ACT 2018.
1.
This approval is for second-stage-of-manufacture WCS Prado 150 based on
first-stage Approval No. 41621 TOYOTA Landcruiser 150 Series issued on 12 Aug
2009.
2.
The Licensee must obtain all second-stage Identification Plates from the
Administrator, as per the contract approved by the Administrator for the supply
of Identification Plates, currently with:
Niddrie
Nameplates Pty Ltd
P.O.
Box 106
Niddrie
VIC
3042
Phone: (03) 9335 2977
Facsimile:
(03) 9335 4357