Pedders Shock Absorber Service Pty Ltd
PO Box 247
NOBLE PARK VIC 3174
ATTENTION:
Mr David Schneiders
Dear Mr Schneiders
The application for a Identification Plate Approval, your reference number G150GVMCA1, our reference number 45905, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.
Your approval number is 45905 and the approval documents are attached.
Yours sincerely
Simon Lilley
Associate Administrator of Vehicle Standards
05 December 2013
GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/
Department of Infrastructure and Regional Development
MOTOR VEHICLE STANDARDS ACT 1989
Section 10A.(1) Approval
Approval No.: 45905
Issue date: 05 December 2013
The Administrator of Vehicle Standards (the Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).
In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.
The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.
This approval is subject to the following conditions.
Approval No.: 45905 Issue Date: 05 December 2013
Schedule 1
Pedders Shock Absorber Service Pty Ltd
6 Bridge Road
KEYSBOROUGH
VIC 3173
Schedule 2
Make : PEDDERS TOYOTA
Model : HILUX 4 X 4
Category : NA
Manufactured by : Pedders Shock Absorber Service Pty Ltd
Typical VIN : MR0FZ22G700123456
Seating Capacity : 2; 4; 5; 6
GVM : 3.14 tonne TO 3.14 tonne
Schedule 3
Expiry date : Life of Model
Plate location : 10 J 32
Plate colour : SILVER
Simon Lilley
Associate Administrator of Vehicle Standards
05 December 2013
Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.
Approval No.: 45905 Issue Date: 05 December 2013
Schedule 4
ADR Document Reference from evidence item
01/00 G150ADR01/00
02/01 G150ADR0201
03/03 G150ADR0303
04/05 G150ADR0405
05/05 G150ADR0505
06/00 G150ADR0600
08/01 G150ADR0801
11/00 G150ADR1100
13/00 G150ADR1300
14/02 G150ADR1402
18/03 G150ADR1803
23/02 (also satisfying 23/01) G150ADR2302
23/02 G150ADR2302
25/02 G150ADR2502
35/03 (also satisfying 31/02) G150SE3503-2
35/03 (also satisfying 31/03) G150SE3503-2
31/35SF G150SF3503
35/03 G150SE3503-2
35/03 (also satisfying 35/04) G150SE3503-2
42/04 G150ADR4204
43/04 G150ADR4304
46/00 G150ADR4600
47/00 G150ADR4700
48/00 G150ADR4800
49/00 G150ADR4900
50/00 G150ADR5000
51/00 G150ADR5100
61/02 G150ADR61021
79/03 G150ADR7903
81/02 G150ADR8102
83/00 G150ADR8300