Pedders Shock Absorber Service Pty Ltd
25 Letcon Drive
dandenong south VIC 3175
ATTENTION:
Mr David Schneiders
Dear Mr Schneiders
The application for a Identification Plate Approval, your reference number iLOADCA-1, our reference number 49771, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.
Your approval number is 49771 and the approval documents are attached.
Yours sincerely
Umesh Shamdasani
Associate Administrator of Vehicle Standards
06 November 2018
GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/
Department of Infrastructure and Regional Development and Cities
MOTOR VEHICLE STANDARDS ACT 1989
Section 14A.(1)(a) Approval
Approval No.: 49771
Issue date: 02 November 2018
The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).
In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.
The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.
This approval is subject to the following conditions.
Approval No.: 49771 Issue Date: 02 November 2018
Schedule 1
Pedders Shock Absorber Service Pty Ltd
25 Letcon Drive
dandenong south
VIC 3175
Schedule 2
Make : Pedders Hyundai
Model : i-Load GVM Plus
Category : NA
Manufactured by : Pedders Shock Absorber Service Pty Ltd
Typical VIN : KMFWBH7JR8U123456
Seating Capacity : 2; 3; 5; 6
GVM : 3.49 tonne TO 3.49 tonne
Schedule 3
Expiry date : Life of Model
Plate location : 30 M 16 Left Hand Side B Pillar
Plate colour : GREEN
NEW LOW VOLUME
UP TO 100 VEHICLES PER ANNUM
Umesh Shamdasani
Associate Administrator of Vehicle Standards
02 November 2018
Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.
Approval No.: 49771 Issue Date: 02 November 2018
Schedule 4
ADR Document Reference from evidence item
01/00 iload0100
04/05 ILOAD0405
06/00 ILOAD0600
08/01 ILOAD0801
10/02 (also satisfying 10/01) ILOAD1002
10/02 ILOAD1002
11/00 ILOAD1100
13/00 ILOADSE1300
14/02 ILOAD1402
18/03 ILOAD1803
22/00 ILOAD2200
23/02 (also satisfying 23/01) ILOAD2302
23/02 ILOAD2302
25/02 ILOAD2502
29/00 ILOAD2900
30/01 iload3001
35/05 (also satisfying 31/03) SEILOAD3505 (Non-Standard, see Schedule 5)
35/05 (also satisfying 31/04) SEILOAD3505 (Non-Standard, see Schedule 5)
31/35SF SFILOAD3135 (Non-Standard, see Schedule 5)
35/05 SEILOAD3505 (Non-Standard, see Schedule 5)
42/04 ILOADSE4204
43/04 ILOADSE4304
46/00 ILOAD4600
47/00 ILOAD4700
48/00 ILOAD4800
49/00 ILOAD4900
51/00 ILOAD5100
61/02 ILOAD6102
79/04 ILOAD7904
81/02 ILOADSE8102
83/00 ILOAD8300
Approval No.: 49771 Issue Date: 02 November 2018
Schedule 5
1. This approval is for second-stage-of-manufacture PEDDERS HYUNDAI Model i-Load GVM Plus based on first-stage Approval No. 38791 HYUNDAI Model TQ-V issued on 31 October 2007.
2. The ADR 35/05 evidence is Not Applicable as the Electronic Stability System has not been tested from the Base vehicle. This is accepted in accordance with Circular 0-4-6 Clause 10,2. This vehicle has as 20mm lift beyond standard only. The vehicle has been tested to the other requirements of ADR 35/05.
3 This vehicle does not have evidence for ADRs 2/01, 3/03 and 5/05 as the base vehicle IPA 38791 has only earlier versions of these rules. This is accepted in accordance with Circular 0-4-6 Clause 4.5
4. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:
Niddrie Nameplates Pty Ltd
P.O. Box 106
Niddrie
VIC 3042
Phone: (03) 9335 2977
Facsimile: (03) 9335 4357