Pedders Shock Absorber Service Pty Ltd
PO Box 247
NOBLE PARK VIC 3174
ATTENTION:
Mr David Schneiders
Dear Mr Schneiders
The application for a Identification Plate Approval, your reference number NAGEN8CA1, our reference number 47825, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.
Your approval number is 47825 and the approval documents are attached.
Yours sincerely
Leon Weekes
Associate Administrator of Vehicle Standards
07 December 2016
GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/
Department of Infrastructure and Regional Development
MOTOR VEHICLE STANDARDS ACT 1989
Section 10A.(2) Approval
Approval No.: 47825
Issue date: 07 December 2016
The Administrator of Vehicle Standards (the Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).
In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.
The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.
This approval is subject to the following conditions.
Approval No.: 47825 Issue Date: 07 December 2016
Schedule 1
Pedders Shock Absorber Service Pty Ltd
6 Bridge Road
KEYSBOROUGH
VIC 3173
Schedule 2
Make : Pedders Toyota
Model : HiLux GVM PLUS
Category : NA
Manufactured by : Pedders Shock Absorber Service Pty Ltd
Typical VIN : MR0HA3CD500372046
Seating Capacity : 2; 4; 5
GVM : 3.1 tonne TO 3.45 tonne
Schedule 3
Expiry date : Life of Model
Plate location : 10 M 20
Plate colour : SILVER
Leon Weekes
Associate Administrator of Vehicle Standards
07 December 2016
Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.
Approval No.: 47825 Issue Date: 07 December 2016
Schedule 4
ADR Document Reference from evidence item
01/00 0100GEN8
02/01 0201GEN8
03/03 0303GEN8
04/05 0405GEN8
05/05 0505GEN8
06/00 0600GEN8
08/01 0801GEN8
10/02 (also satisfying 10/01) 1002GEN8
10/02 1002GEN8
11/00 1100GEN8
13/00 1300GEN8
14/02 1402GEN8
18/03 1803GEN8
23/02 (also satisfying 23/01) 2302GEN8
23/02 2302GEN8
25/02 2502GEN8
29/00 2900GEN8
30/01 3001GEN8
35/05 (also satisfying 31/03) 3505SEGEN8-1 (Minor Non-Compliance, see Schedule 5)
35/05 (also satisfying 31/03) 3505SEGEN81
31/35SF 3505SFGEN8
31/35SF 3505SFGEN8-1
31/35SF 3505SFGEN8-2
35/05 3505SEGEN8-1 (Minor Non-Compliance, see Schedule 5)
35/05 3505SEGEN81
42/04 4204GEN8
43/04 4304GEN8
45/01 4501GEN8
46/00 4600GEN8
47/00 4600GEN8
48/00 4800GEN8
49/00 4900GEN8
50/00 5000GEN8
51/00 5100GEN8
61/02 6102GEN8
69/00 6900GEN8
72/00 7200GEN8
76/00 7600GEN8
79/04 (also satisfying 79/03) 7904GEN8
79/04 7904GEN8
81/02 8102GEN8
83/00 8300GEN8
Approval No.: 47825 Issue Date: 07 December 2016
Schedule 5
1. This approval is for second-stage-manufacturer Pedders Shock Absorber Service Pty Ltd for the Pedders Toyota HiLux GVM Plus, based on first-stage approval no. 47341 Toyota Hilux 8GEN.
This vehicle does not fully comply with Australian Design Rule 35/05 - Commercial Vehicle Brake Systems. The Brake Assist System has not been re-tested following the second stage of manufacture by Pedders Shock Absorber Service Pty Ltd, as required by required by clause 4.1.1.1 of ADR 35/05.
This non-compliance in considered minor and inconsequential by the Administrator.
2. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:
Niddrie Nameplates Pty Ltd
P.O. Box 106
Niddrie
VIC 3042
Phone: (03) 9335 2977
Facsimile: (03) 9335 4357
3. The 'chassis-cab' variants of the MAKE&MODEL vehicle type do not comply with the position requirements of ADR13/00 for the following lamps and reflectors:
- reversing lamps
- rear direction indicator lamps
- rear reflex reflectors
- rear registration plate lamps
- rear position (side) lamps
- stop lamps
4. The 'chassis-cab' variants of the MAKE&MODEL vehicle type do not comply with:
- clause 14.2 of ADR42/04 for wheel guards on the rearmost wheels.
- clause 9.1.1.1 of ADR61/02 for provision of a rear registration plate.
5. The manufacturer must provide instructions, guidelines and references to the relevant ADRs, that must be met, to whoever is responsible for completing chassis-cab vehicles certified in accordance with Circular 0-4-11 prior to their supply to the market.