Pedders Shock Absorber Service Pty Ltd
PO Box 247
NOBLE PARK VIC 3174
ATTENTION:
Mr David Schneiders
Dear Mr Schneiders
The application for a Identification Plate Approval, your reference number MC200CA-1, our reference number 48677, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.
Your approval number is 48677 and the approval documents are attached.
Yours sincerely
David Morton
Associate Administrator of Vehicle Standards
08 January 2018
GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/
Department of Infrastructure and Regional Development and Cities
MOTOR VEHICLE STANDARDS ACT 1989
Section 10A.(3) Approval
Approval No.: 48677
Issue date: 08 January 2018
The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).
In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.
The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.
This approval is subject to the following conditions.
Approval No.: 48677 Issue Date: 08 January 2018
Schedule 1
Pedders Shock Absorber Service Pty Ltd
25 Letcon Drive
dandenong south
VIC 3175
Schedule 2
Make : Pedders Toyota
Model : Landcruiser 200 GVM Plus
Category : MC
Manufactured by : Pedders Shock Absorber Service Pty Ltd
Typical VIN : JTMHV05J804103407
Seating Capacity : 7; 8
Schedule 3
Expiry date : Life of Model
Plate location : 10 M 22 Right Hand Side B Pillar
Plate colour : GREEN
NEW LOW VOLUME
UP TO 100 VEHICLES PER ANNUM
David Morton
Associate Administrator of Vehicle Standards
08 January 2018
Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.
Approval No.: 48677 Issue Date: 08 January 2018
Schedule 4
ADR Document Reference from evidence item
01/00 J200ADR0100
02/01 J200ADR0201
03/03 J200ADR0303
04/05 J200ADR0405
05/05 J200ADR0505
06/00 J200ADR0600
08/01 J200ADR0801
11/00 J200ADR01100
13/00 J200SE1300-1
14/02 J200ADR01402
18/03 J200ADR01803
23/02 (also satisfying 23/01) J200ADR02302
23/02 J200ADR02302
25/02 J200ADR02502
29/00 J200ADR02900
30/01 J200ADR3001
35/05 (also satisfying 31/03) MC2003505-1
35/05 (also satisfying 31/03) MC2003505-2
35/05 (also satisfying 31/04) MC2003505-1
35/05 (also satisfying 31/04) MC2003505-2
31/35SF MC200SF31352
34/02 (also satisfying 34/01) J200ADR3402
34/02 J200ADR3402
35/05 MC2003505-1
35/05 MC2003505-2
42/04 MC200ADR4204
43/04 MC200SE4304
46/00 J200ADR4600
77/00 (also satisfying 46/00) J200ADR7700
47/00 J200ADR4700
48/00 J200ADR4800
49/00 J200ADR4900
50/00 J200ADR5000
51/00 J200ADR5100
60/00 J200ADR6000
61/02 J200ADR6102
62/02 J200ADR6202
69/00 J200ADR6900
75/00 J200ADR7500
76/00 J200ADR7600
77/00 J200ADR7700
78/00 J200ADR7800
79/04 J200ADR7904
81/02 J200ADR8102
82/00 J200ADR8200
83/00 J200ADR8300
Approval No.: 48677 Issue Date: 08 January 2018
Schedule 5
1. This approval is for second-stage-of-manufacture (make) PEDDERS TOYOTA (model) LANDCRUISER 200 GVM PLUS based on first-stage Approval No. 38469 TOYOTA LANDCRUISER 200 SER issued on 7 September 2007.
2. The Licensee to whom this Approval is issued is limited to placing Low Volume Identification Plates to no more than 300 vehicles within each 12 month period, following the date of first issue of a Low Volume approval, to vehicles within the Category specified in Schedule 2. In addition, the Licensee is restricted to 100 plates for each Low Volume Identification Plate Approval it holds. The 300 vehicle limit applies regardless of the number of Low Volume Approvals the Licensee may hold.
3. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:
Niddrie Nameplates Pty Ltd
P.O. Box 106
Niddrie
VIC 3042
Phone: (03) 9335 2977
Facsimile: (03) 9335 4357