Pedders Shock Absorber Service Pty Ltd
PO Box 247
NOBLE PARK VIC 3174
ATTENTION:
Mr David Schneiders
Dear Mr Schneiders
The application for a Identification Plate Approval, your reference number MUX4WDCA-2, our reference number 48678, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.
Your approval number is 48678 and the approval documents are attached.
Yours sincerely
David Morton
Associate Administrator of Vehicle Standards
08 January 2018
GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/
Department of Infrastructure and Regional Development and Cities
MOTOR VEHICLE STANDARDS ACT 1989
Section 10A.(3) Approval
Approval No.: 48678
Issue date: 08 January 2018
The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).
In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.
The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.
This approval is subject to the following conditions.
Approval No.: 48678 Issue Date: 08 January 2018
Schedule 1
Pedders Shock Absorber Service Pty Ltd
25 Letcon Drive
dandenong south
VIC 3175
Schedule 2
Make : Pedders Isuzu
Model : MU-X 4WD GVM Plus
Category : MC
Manufactured by : Pedders Shock Absorber Service Pty Ltd
Typical VIN : MPAUCS85GHT000219
Seating Capacity : 7
Schedule 3
Expiry date : Life of Model
Plate location : 9 I 15 - Centre of Firewall directly behind engine.
Plate colour : GREEN
NEW LOW VOLUME
UP TO 100 VEHICLES PER ANNUM
David Morton
Associate Administrator of Vehicle Standards
08 January 2018
Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.
Approval No.: 48678 Issue Date: 08 January 2018
Schedule 4
ADR Document Reference from evidence item
01/00 MUX4WD0100
02/01 MUX4WD0201
03/03 MUX4WD03031
04/05 MUX4WD0303
04/05 MUX4WD0405
05/05 MUX4WD0505
06/00 MUX4WD0600
08/01 MUX4WD0801
10/02 (also satisfying 10/01) MUX4WD1002
10/02 MUX4WD1002
11/00 MUX4WD1100
13/00 SEMUXW41300
14/02 MUX4WD1402
18/03 MUX4WD1803
23/02 (also satisfying 23/01) MUX4WD2302
23/02 MUX4WD2302
25/02 MUX4WD2502
29/00 MUX4WD2900
30/01 MUX4WD3001
35/05 (also satisfying 31/03) SEMUX43505-2
35/05 (also satisfying 31/04) SEMUX43505-2
31/35SF SFMUX4WD3135
34/02 (also satisfying 34/01) MUX4WD3402
34/02 MUX4WD3402
35/05 SEMUX43505-2
42/04 MUX4WD4204
42/04 SE4204MUX
43/04 MUX4304-1
74/00 (also satisfying 45/01) MUX4WD7400
46/00 MUX4WD4600
47/00 MUX4WD4700
48/00 MUX4WD4800
49/00 MUX4WD4900
50/00 MUX4WD5000
51/00 MUX4WD5100
61/02 MUX4WD6102
69/00 MUX4WD6900
72/00 MUX4WD7200
74/00 MUX4WD7400
76/00 MUX4WD7600
79/04 MUX4WD7904
81/02 MUX4WD8102
82/00 MUX4WD8200
83/00 MUX4WD8300
Approval No.: 48678 Issue Date: 08 January 2018
Schedule 5
1. This approval is for second-stage-of-manufacture (make) PEDDERS ISUZU (model) MU-X 4WD GVM PLUS based on first-stage Approval No. 45455 ISUZU MU-X 4WD first issued on 20 August 2013.
2. The Licensee to whom this Approval is issued is limited to placing Low Volume Identification Plates to no more than 300 vehicles within each 12 month period, following the date of first issue of a Low Volume approval, to vehicles within the Category specified in Schedule 2. In addition, the Licensee is restricted to 100 plates for each Low Volume Identification Plate Approval it holds. The 300 vehicle limit applies regardless of the number of Low Volume Approvals the Licensee may hold.
3. The Licensee must obtain all identification plates from a plate contractor approved by the Administrator. Currently the contractor approved by the Administrator for the supply of Identification Plates is:-
Niddrie Nameplates Pty Ltd
P.O. Box 106
Niddrie
VIC 3042
Phone: (03) 9335 2977
Facsimile: (03) 9335 4357