General Motors Corporation

PO Box 9020

MC 480-210-2V1

Warren Micgigan 48090-9020

U.S.A

ATTENTION: Mr Kim Nguyen

 

Dear Mr Nguyen

The application for a Identification Plate Approval, your reference number CAEGR1CHRD01, our reference number 43723, lodged for General Motors Corporation, has been approved.

Your approval number is 43723 and the approval documents are attached.

Yours sincerely

for Administrator of Vehicle Standards

09 December 2011

 

 

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Transport

MOTOR VEHICLE STANDARDS ACT 1989

Section 10A.(1) Approval

Approval No.: 43723

Issue date: 09 December 2011

The Administrator of Vehicle Standards (the Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.

Approval No.: 43723 Issue Date: 09 December 2011

Schedule 1

General Motors Corporation

30001 Van Dyke Bldgs 2-10

Warren

Michigan 48090-9020

U.S.A

 

Schedule 2

Make : HOLDEN

Model : VOLT

Category : MA

Manufactured by : General Motors Corporation

Typical VIN : 5G8RZ6E40DU100001

Seating Capacity : 4

 

Schedule 3

Expiry date : Life of Model

Plate location : On the left side B pillar

Plate colour : WHITE W BLACK LETTER

Administrator of Vehicle Standards

09 December 2011

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 43723 Issue Date: 09 December 2011

Schedule 4

ADR Document Reference from evidence item

01/00 01EGR1CHRD00

02/01 02EGR1CHRD00

03/03 03EGR1CHRD00

03/03 03EGR1CHRD01

03/03 03EGR1CHRD02

03/03 03EGR1CHRD03

04/04 04EGR1CHRD00

04/04 04EGR1CHRD01

04/04 04EGR1CHRD02

04/04 04EGR1CHRD03

05/05 05EGR1CHRD00

06/00 06EGR1CHRD00

06/00 06EGR1CHRD01

06/00 06EGR1CHRD02

08/01 08EGR1CHRD00

10/02 (also satisfying 10/01) 10EGR1CHRD00

10/02 10EGR1CHRD00

11/00 11EGR1CHRD00

13/00 13EGR1CHRD02

14/02 14EGR1CHRD00

18/03 18EGR1CHRD00

21/00 21EGR1CHRD00

23/02 (also satisfying 23/01) 23EGR1CHRD00

23/02 23EGR1CHRD00

25/02 25EGR1CHRD00

29/00 29EGR1CHRD00

31/02 31EGR1CHRD00

31/35SF 31FGR1CHRD00

34/01 34EGR1CHRD00

42/04 42EGR1CHRD00

43/04 43EGR1CHRD00

74/00 (also satisfying 45/01) 74EGR1CHRD00

46/00 46EGR1CHRD00

47/00 47EGR1CHRD00

48/00 48EGR1CHRD00

49/00 49EGR1CHRD00

49/00 49EGR1CHRD01

49/00 49EGR1CHRD02

49/00 49EGR1CHRD03

51/00 51EGR1CHRD00

52/00 52EGR1CHRD00

60/00 60EGR1CHRD00

61/02 61EGR1CHRD00

69/00 69EGR1CHRD00

72/00 72EGR1CHRD00

73/00 73EGR1CHRD00

74/00 74EGR1CHRD00

76/00 76EGR1CHRD00

79/02 79EGR1CHRD00

79/02SF 79FGR1CHRD00

81/02 81EGR1CHRD02

81/02 SF 81FGR1CHRD00

82/00 82EGR1CHRD00

83/00 83EGR1CHRD00

83/00SF 83FGR1CHRD00