Jenkins Springs Pty Ltd

PO Box 398

BASSENDEAN WA 6934

ATTENTION: Mr James McCully

 

Dear Mr McCully

The application for a Identification Plate Approval, your reference number CAWCSFR204, our reference number 47899, lodged for Jenkins Springs Pty Ltd, has been approved.

Your approval number is 47899 and the approval documents are attached.

Yours sincerely

Umesh Shamdasani

Associate Administrator of Vehicle Standards

13 August 2018

 

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Regional Development and Cities

MOTOR VEHICLE STANDARDS ACT 1989

Section 10A.(1) Approval

Approval No.: 47899

Issue date: 13 August 2018

The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administratorís circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that ruleís distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administratorís Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.
  11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 47899 Issue Date: 13 August 2018

Schedule 1

Jenkins Springs Pty Ltd

188 Railway Parade

BASSENDEAN

WA 6054

 

Schedule 2

Make : WCS FORD

Model : WCS FORD RANGER2

Category : NA

Manufactured by : Jenkins Springs Pty Ltd

Typical VIN : MNAUMEF50FW530339

Seating Capacity : 2; 3; 4; 5

GVM : 3.5 tonne TO 3.5 tonne

 

Schedule 3

Expiry date : Life of Model

Plate location : DRIVERS SIDE DOOR SILL

Plate colour : SILVER

Umesh Shamdasani

Associate Administrator of Vehicle Standards

13 August 2018

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 47899 Issue Date: 13 August 2018

Schedule 4

ADR Document Reference from evidence item

01/00 0100WCSFR2

02/01 0201WCSFR2

03/03 0303WCSFR2

04/05 0405WCSFR2

05/05 0505WCSFR2

06/00 0600WCSFR2

08/01 0801WCSFR2

11/00 1100WCSFR2

13/00 1300WCSFR2

14/02 1402WCSFR2

18/03 1803WCSFR2

23/02 (also satisfying 23/01) 2302WCSFR2

23/02 2302WCSFR2

25/02 2502WCSFR2

31/03 3103WCSFR2

35/05 (also satisfying 31/03) 3505WCSFR202

35/05 (also satisfying 31/03) 3505WCSFR203

35/05 (also satisfying 31/04) 3505WCSFR202

35/05 (also satisfying 31/04) 3505WCSFR203

31/35SF 31SFWCSFR202

35/05 3505WCSFR202

35/05 3505WCSFR203

31/03 (also satisfying 35/05) 3103WCSFR2

42/04 4204WCSFR202

43/04 4304WCSFR2

46/00 4600WCSFR2

47/00 4700WCSFR2

48/00 4800WCSFR2

49/00 4900WCSFR2

51/00 5100WCSFR2

61/02 6102WCSFR201

62/02 6202WCSFR2

79/04 7904WCSFR202

81/02 8102WCSFR202

83/00 8300WCSFR2

Approval No.: 47899 Issue Date: 13 August 2018

Schedule 5

 

1. This WCS Ford (Vehicle Make) WCS FORD RANGER2 (Vehicle Model) approval is a second-stage-manufacture GVM UPGRADE based on the first-stage Approval No. 43280 FORD RANGER 2 first issued on the 28 June 2011.

2. The 'chassis-cab' variants of the WCS Ford (Vehicle Make) WCS FORD RANGER2 (Vehicle Model) vehicle type do not comply with the position requirements of ADR 13/00 for the following lamps and reflectors:

- reversing lamps

- rear direction indicator lamps

- rear reflex reflectors

- rear registration plate lamps

- rear position (side) lamps

- stop lamps

3. The 'chassis-cab' variants of the WCS Ford (Vehicle Make) WCS FORD RANGER2 (Vehicle Model) vehicle type do not comply with:

- clause 14.2. of ADR 42/04 for wheel guards on the rearmost wheels.

- clause 9.1.1.1. of ADR 61/02 for provision of a rear registration plate.

4. The manufacturer must provide instructions, guidelines and references to the relevant ADRs, that must be met, to whoever is responsible for completing chassis-cab vehicles certified in accordance with Circular 0-4-11 prior to their supply to the market.

Use of these 'chassis-cab' vehicles certified in accordance with Circular 0-4-11 are therefore subject to any conditions that may be imposed by the relevant Registering Authorities

5. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:

Niddrie Nameplates Pty Ltd

P.O. Box 106

Niddrie

VIC 3042

Phone: (03) 9335 2977

Facsimile: (03) 9335 4357