Pedders Shock Absorber Service Pty Ltd

PO Box 247

NOBLE PARK VIC 3174

ATTENTION: Mr David Schneiders

 

Dear Mr Schneiders

The application for a Identification Plate Approval, your reference number GUNBCA-3, our reference number 47524, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.

Your approval number is 47524 and the approval documents are attached.

Yours sincerely

Umesh Shamdasani

Associate Administrator of Vehicle Standards

13 October 2015

 

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Regional Development

MOTOR VEHICLE STANDARDS ACT 1989

Section 14A.(1)(a) Approval

Approval No.: 47524

Issue date: 13 October 2015

The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administratorís circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that ruleís distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administratorís Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.
  11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 47524 Issue Date: 13 October 2015

Schedule 1

Pedders Shock Absorber Service Pty Ltd

6 Bridge Road

KEYSBOROUGH

VIC 3173

 

Schedule 2

Make : Pedders Nissan

Model : Patrol NB

Category : NB1

Manufactured by : Pedders Shock Absorber Service Pty Ltd

Typical VIN : JN1TESY61A0401886

Seating Capacity : 2; 5

GVM : 3.505 tonne TO 3.95 tonne

 

Schedule 3

Expiry date : Life of Model

Plate location : 28 M 9

Plate colour : SILVER

Umesh Shamdasani

Associate Administrator of Vehicle Standards

13 October 2015

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 47524 Issue Date: 13 October 2015

Schedule 4

ADR Document Reference from evidence item

01/00 GUNB0100

02/00 GUNB0200

03/02 GUNB0302

04/05 GUNB0405

05/04 GUNB0504

06/00 GUNB0600-3

06/00 GUNB0600-4

08/01 GUNB0801

11/00 GUNB1100

13/00 GUNB1300

14/02 GUNB1402

18/03 NGUNB1803

30/01 GUNB3001

31/35SF GUNBSF3504-1

31/35SF GUNBSF35041

35/04 GUNBSE3504

35/04 GUNBSE35041

35/04 (also satisfying 35/05) GUNBSE3504

35/04 (also satisfying 35/05) GUNBSE35041

42/04 GUNB4204

43/04 GUNB4304

45/01 GUNBSE4501

46/00 GUNB4600

47/00 GUNB4700

48/00 GUNB4800

49/00 GUNB4900

50/00 GUNB5000

51/00 GUNB5100

61/02 GUNB6102

62/02 GUNB6202

80/03 GUNB8003 (Non-Standard, see Schedule 5)

83/00 GUNB8300

Approval No.: 47524 Issue Date: 13 October 2015

Schedule 5

 

 

 

. The Approval is for second-stage-of-manufacture PEDDERS NISSAN PATROL NB based on first-stage Approval No. 12483 NISSAN Y61 COMMERCIAAL issued on 11th December 1997.

 

2. This vehicle has not been tested to demonstrate compliance with:

2.1 ADR 80/03 " Emission Control for Heavy Vehicles"

" Administrator's Circular 79/00-1-1 provides for this second-stage-of-manufacture vehicle an extension of ADR 79/01 evidence.

This non-compliance is non-standard.

 

3. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:

Niddrie Nameplates Pty Ltd

P O Box 106

Niddrie

VIC 3042

Phone: (03) 9335 2977

Facsimile: (03) 9335 4357