Equipcon Pty Ltd

PO Box 570

South Morang VIC 3752

ATTENTION: Mr Carlo Guardiani

 

Dear Mr Guardiani

The application for a Identification Plate Approval, your reference number CA-EQP-3, our reference number 42424, lodged for Equipcon Pty Ltd, has been approved.

Your approval number is 42424 and the approval documents are attached.

Yours sincerely

for Administrator of Vehicle Standards

17 January 2011

 

 

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Transport

MOTOR VEHICLE STANDARDS ACT 1989

Section 14A.(1)(a) Approval

Approval No.: 42424

Issue date: 17 January 2011

The Administrator of Vehicle Standards (the Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administratorís circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that ruleís distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administratorís Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.
  11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 42424 Issue Date: 17 January 2011

Schedule 1

Equipcon Pty Ltd

7 Stanley Jones Dr

South Morang

VIC 3752

 

Schedule 2

Make : Equipcon

Model : C Pump DAF CF 7585 8x4

Category : NC

Manufactured by : Equipcon Pty Ltd

Typical VIN : XRLAT85XC2E500998

Seating Capacity : 2

GVM : 28 tonne TO 44 tonne

 

Schedule 3

Expiry date : Life of Model

Plate location : On the driver side door frame to be visible when the door is open

Plate colour : GREEN

SECOND STAGE OF MANUFACTURE

UP TO 100 VEHICLES PER ANNUM

Administrator of Vehicle Standards

17 January 2011

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 42424 Issue Date: 17 January 2011

Schedule 4

ADR Document Reference from evidence item

01/00 1-EQP-1

01/00 1-EQP-2

04/03 4-EQP-1

05/05 5-EQP-1

06/00 6-EQP-1

06/00 6-EQP-2

06/00 6-EQP-3

08/01 8-EQP-1

13/00 13-EQP-1

14/02 14-EQP-1

18/03 18-EQP-1

30/01 30-EQP-1

31/35SF 35-EQP-2

35/02 35-EQP-1

35/02 (also satisfying 35/03) 35-EQP-1

35/02 (also satisfying 35/03) 35-EQP-1

42/04 42-EQP-1

43/04 43-43M-1 (Non-Standard, see Schedule 5)

45/01 45-EQP-2

46/00 46-45M-1

46/00 46-EQP-1

47/00 47-EQP-1

47/00 47-EQP-2

48/00 48-EQP-1

49/00 49-EQP-1

49/00 49-EQP-2

49/00 49-EQP-3

50/00 50-EQP-1

51/00 51-EQP-1

52/00 52-EQP-1

61/02 61-EQP-2

65/00 65-EQP-1

80/03 80-EQP-1

83/00 83-EQP-1

Approval No.: 42424 Issue Date: 17 January 2011

Schedule 5

 

 

1. This approval is for a second-stage-of-manufacture EQUIPCON C PUMP DAF CF 7585 8x4 based on first-stage Approval No. 29025 DAF CF 7585 8x4 issued on 20th November 2002.

2. The vehicle does not comply with ADR 43/04, Clause 6.2.3, the "rear overhang" is greater than 3.7 metres.

Use of the vehicle may be subject to conditions imposed by State & Territory Registering Authorities.

3. The Licensee to whom this Approval is given may not place identification plates to more than 100 vehicles each financial year to vehicles in the vehicle category specified in Schedule 2. This vehicle limit applies regardless of the number of Approvals the Licensee may hold.

4. The Licensee must obtain all identification plates from a plate contractor approved by the Administrator. Currently the contractor approved by the Administrator for the supply of Identification Plates is:-

Niddrie Nameplates Pty Ltd

P.O. Box 106

Niddrie

VIC 3042

Phone: (03) 9335 2977

Facsimile: (03) 9335 4357