Jenkins Springs Pty Ltd

PO Box 398

BASSENDEAN WA 6934

ATTENTION: Mr James McCully

 

Dear Mr McCully

The application for a Identification Plate Approval, your reference number CAWCS2LC03, our reference number 49103, lodged for Jenkins Springs Pty Ltd, has been approved.

Your approval number is 49103 and the approval documents are attached.

Yours sincerely

Umesh Shamdasani

Associate Administrator of Vehicle Standards

20 April 2018

 

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Regional Development and Cities

MOTOR VEHICLE STANDARDS ACT 1989

Section 10A.(3) Approval

Approval No.: 49103

Issue date: 19 April 2018

The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.
  11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 49103 Issue Date: 19 April 2018

Schedule 1

Jenkins Springs Pty Ltd

188 Railway Parade

BASSENDEAN

WA 6054

 

Schedule 2

Make : WCS TOYOTA

Model : WCS LANDCRUISER 200

Category : NB1

Manufactured by : Jenkins Springs Pty Ltd

Typical VIN : JTMGV09J601234567

Seating Capacity : 5

GVM : 3.8 tonne TO 3.8 tonne

 

Schedule 3

Expiry date : Life of Model

Plate location : Passenger side B pillar of vehicle

Plate colour : GREEN

NEW LOW VOLUME

UP TO 100 VEHICLES PER ANNUM

 

Umesh Shamdasani

Associate Administrator of Vehicle Standards

19 April 2018

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 49103 Issue Date: 19 April 2018

Schedule 4

ADR Document Reference from evidence item

01/00 0100WCS2LC01

03/03 0303WCS2LC01

04/05 0405WCS2LC01

05/05 0505WCS2LC01

06/00 0600WCS2LC01

08/01 0801WCS2LC01

11/00 1100WCS2LC01

13/00 1300WCS2LC02

14/02 1402WCS2LC01

18/03 1803WCS2LC01

30/01 3001WCS2LC01

31/35SF 31SFWCS2LC01

35/05 3505WCS2LC02

42/04 4204WCS2LC02

43/04 4304WCS2LC02

46/00 4600WCS2LC01

47/00 4700WCS2LC01

48/00 4800WCS2LC01

49/00 4900WCS2LC01

51/00 5100WCS2LC01

61/02 6102WCS2LC01

62/02 6202WCS2LC01

80/03 8003WCS2LC03

83/00 8300WCS2LC01

Approval No.: 49103 Issue Date: 19 April 2018

Schedule 5

 

1. This approval is for GVM UPGRADE second-stage-of-manufacture WCS Toyota/WCS Landcruiser based on first-stage Approval No.43656 issued on 31 Aug 2011.

2. The Licensee to whom this Approval is issued is limited to placing Identification Plates to no more than 100 vehicles within each 12 month period, following the date of issue of the approval, to vehicles within the Category specified in Schedule This vehicle limit applies regardless of the number of Approvals the Licensee may hold.

3. The Licensee must obtain all identification plates from a plate contractor approved by the Administrator. Currently the contractor approved by the Administrator for the supply of Identification Plates is:-

Niddrie Nameplates Pty Ltd

P.O. Box 106

Niddrie

VIC 3042

Phone: (03) 9335 2977

Facsimile: (03) 9335 4357