Pedders Shock Absorber Service Pty Ltd

PO Box 247

NOBLE PARK VIC 3174

ATTENTION: Mr David Schneiders

Dear Mr Schneiders

The application for a Identification Plate Approval, your reference number P150CA-1, our reference number 49606, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.

Your approval number is 49606 and the approval documents are attached.

Yours sincerely

Linda Rasmussen

Associate Administrator of Vehicle Standards

03 December 2018

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

Department of Infrastructure and Regional Development and Cities

MOTOR VEHICLE STANDARDS ACT 1989

Section 10A.(3) Approval

Approval No.: 49606

Issue date: 24 July 2018

The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.

2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.

3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.

4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.

5. The Licensee shall maintain records of detailed quality control and test documentation.

6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.

7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.

8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).

9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.

10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.

11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 49606 Issue Date: 24 July 2018

Schedule 1

Pedders Shock Absorber Service Pty Ltd

25 Letcon Drive

dandenong south

VIC 3175

Schedule 2

Make : Pedders Toyota

Model : Prado 150 GVM Plus

Category : MC

Manufactured by : Pedders Shock Absorber Service Pty Ltd

Typical VIN : JTEBR3FJ30K086503

Seating Capacity : 5; 7

Schedule 3

Expiry date : 01 November 2021

Plate location : 10 M 19 Left Hand Side B Pillar

Plate colour : GREEN

NEW LOW VOLUME

UP TO 100 VEHICLES PER ANNUM

Linda Rasmussen

Associate Administrator of Vehicle Standards

24 July 2018

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 49606 Issue Date: 24 July 2018

Schedule 4

ADR Document Reference from evidence item

01/00 P150ADR0100

02/01 P150ADR0201

03/03 P150ADR03031

04/05 P150ADR0405

05/05 P150ADR0505

06/00 P150ADR0600

08/01 P150ADR0801

11/00 P150ADR01100

13/00 P150SE1300-1

14/02 P150ADR01402

18/03 P150ADR01803

23/02 (also satisfying 23/01) P150ADR02302

23/02 P150ADR02302

25/02 P150ADR02502

29/00 P150ADR02900

30/01 P150ADR3001

35/05 (also satisfying 31/03) P1503505-1

35/05 (also satisfying 31/04) P1503505-1

31/35SF P150SF3135

34/02 (also satisfying 34/01) P150ADR3402

34/02 P150ADR3402

35/05 P1503505-1

42/04 P150ADR4204

43/04 P150SE4304

46/00 P150ADR4600

77/00 (also satisfying 46/00) P150ADR7700

47/00 P150ADR4700

48/00 P150ADR4800

49/00 P150ADR4900

50/00 P150ADR5000

51/00 P150ADR5100

60/00 P150ADR6000

61/02 P150ADR6102

62/02 P150ADR6202

69/00 P150ADR6900

72/00 P150ADR7200

75/00 P150ADR7500

76/00 P150ADR7600

77/00 P150ADR7700

78/00 P150ADR7800

79/04 P150ADR7904

81/02 P150ADR8102

82/00 P150ADR8200

83/00 P150ADR8300