Pedders Shock Absorber Service Pty Ltd

PO Box 247

NOBLE PARK VIC 3174

ATTENTION: Mr David Schneiders

 

Dear Mr Schneiders

The application for a Identification Plate Approval, your reference number BT50GVMCA02, our reference number 45474, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.

Your approval number is 45474 and the approval documents are attached.

Yours sincerely

 

Umesh Shamdasani

Associate Administrator of Vehicle Standards

27 February 2015

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Regional Development

MOTOR VEHICLE STANDARDS ACT 1989

Section 10A.(1) Approval

Approval No.: 45474

Issue date: 27 February 2015

The Administrator of Vehicle Standards (the Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administratorís circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that ruleís distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administratorís Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.
  11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 45474 Issue Date: 27 February 2015

Schedule 1

Pedders Shock Absorber Service Pty Ltd

6 Bridge Road

KEYSBOROUGH

VIC 3173

 

Schedule 2

Make : PEDDERS MAZDA

Model : BT50

Category : NA

Manufactured by : Pedders Shock Absorber Service Pty Ltd

Typical VIN : MMOUPOYF100112415

Seating Capacity : 2; 3; 4; 5

GVM : 3.33 tonne TO 3.5 tonne

 

Schedule 3

Expiry date : Life of Model

Plate location : 12 N 12

Plate colour : SILVER

Umesh Shamdasani

Associate Administrator of Vehicle Standards

27 February 2015

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 45474 Issue Date: 27 February 2015

Schedule 4

ADR Document Reference from evidence item

01/00 BT50ADR01/00

02/01 BT50ADR0201

03/03 BT50ADR0303

04/05 BT50ADR04052

05/05 BT50ADR0505

06/00 BT50ADR0600

08/01 BT50ADR0801

10/02 (also satisfying 10/01) BT50SE1002

10/02 BT50SE1002

11/00 BT50ADR1100

13/00 BT50ADR1300

14/02 BT50ADR1402

18/03 BT50ADR1803

23/02 (also satisfying 23/01) BT50ADR2302

23/02 BT50ADR2302

25/02 BT50ADR2502

29/00 BT50SE2900

31/02 (using 35/03) BT50SE3503-1

31/02 (using 35/03) BT50SE3503-2

35/04 (also satisfying 31/02) BT50SE3504

31/35SF SF3135BT50

31/35SF SF3135BT50-1

35/04 BT50SE3504

35/04 (using 35/03) BT50SE3503-1

35/04 (using 35/03) BT50SE3503-2

42/04 BT50ADR42041

43/04 BT50ADR4304

44/02 BT50SE4400

46/00 BT50ADR46001

47/00 BT50ADR47001

48/00 BT50ADR48001

49/00 BT50ADR49001

50/00 BT50ADR50001

51/00 BT50ADR51001

61/02 BT50ADR61021

62/02 BT50ADR62021

69/00 BT50SE6900

72/00 BT50SE7200

79/02 BT50ADR79021

81/02 BT50ADR81021

83/00 BT50ADR83001

Approval No.: 45474 Issue Date: 27 February 2015

Schedule 5

 

1. This approval is for second-stage-of-manufacture PEDDERS MAZDA BT50based on first-stage Approval No. 43491 MAZDA BT50 issued on 28 June 2011

2. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:

Niddrie Nameplates Pty Ltd

P.O. Box 106

Niddrie

VIC 3042

Phone: (03) 9335 2977

Facsimile: (03) 9335 4357