Pedders Shock Absorber Service Pty Ltd
PO Box 247
NOBLE PARK VIC 3174
ATTENTION:
Mr David Schneiders
Dear Mr Schneiders
The application for a Identification Plate Approval, your reference number NA200CA, our reference number 47168, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.
Your approval number is 47168 and the approval documents are attached.
Yours sincerely
Umesh Shamdasani
Associate Administrator of Vehicle Standards
27 March 2015
GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/
Department of Infrastructure and Regional Development
MOTOR VEHICLE STANDARDS ACT 1989
Section 10A.(1) Approval
Approval No.: 47168
Issue date: 27 March 2015
The Administrator of Vehicle Standards (the Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).
In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.
The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.
This approval is subject to the following conditions.
Approval No.: 47168 Issue Date: 27 March 2015
Schedule 1
Pedders Shock Absorber Service Pty Ltd
6 Bridge Road
KEYSBOROUGH
VIC 3173
Schedule 2
Make : PEDDERS TOYOTA
Model : HIACE
Category : NA
Manufactured by : Pedders Shock Absorber Service Pty Ltd
Typical VIN : JTFHX02P500001001
Seating Capacity : 2; 5
GVM : 3.19 tonne TO 3.46 tonne
Schedule 3
Expiry date : Life of Model
Plate location : 19 I 22
Plate colour : SILVER
Umesh Shamdasani
Associate Administrator of Vehicle Standards
27 March 2015
Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.
Approval No.: 47168 Issue Date: 27 March 2015
Schedule 4
ADR Document Reference from evidence item
01/00 NA200HI0100
02/01 NA200HI0201
03/03 NA200HI0303
04/05 NA200HI04051
05/05 NA200HI0505
06/00 NA200HI0600
08/01 NA200HI0801
10/01 NA200HI1001
10/01 (also satisfying 10/02) NA200HI1001
11/00 NA200HI1100
13/00 NA200HI1300
14/02 NA200HI1402
18/03 NA200HI1803
25/02 NA200HI2502
30/01 NA200HI3001
35/04 (also satisfying 31/02) NA200HI3504
31/35SF NA200HISF31
35/04 NA200HI3504
42/04 NA200HI4204
43/04 NA200HI4304
46/00 NA200HI4600
47/00 NA200HI4700
48/00 NA200HI4800
49/00 NA200HI4900
51/00 NA200HI5100
61/02 NA200HI6102
81/02 NA200HI8102
83/00 NA200HI8300