Pedders Shock Absorber Service Pty Ltd
PO Box 247
NOBLE PARK VIC 3174
ATTENTION:
Mr David Schneiders
Dear Mr Schneiders
The application for a Identification Plate Approval, your reference number RGCOL2WDCA03, our reference number 45672, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.
Your approval number is 45672 and the approval documents are attached.
Yours sincerely
Umesh Shamdasani
Associate Administrator of Vehicle Standards
28 August 2015
GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/
Department of Infrastructure and Regional Development
MOTOR VEHICLE STANDARDS ACT 1989
Section 10A.(1) Approval
Approval No.: 45672
Issue date: 28 August 2015
The Administrator of Vehicle Standards (the Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).
In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.
The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.
This approval is subject to the following conditions.
Approval No.: 45672 Issue Date: 28 August 2015
Schedule 1
Pedders Shock Absorber Service Pty Ltd
6 Bridge Road
KEYSBOROUGH
VIC 3173
Schedule 2
Make : PEDDERS
Model : HOLDEN RG COLORADO 2WD
Category : NA
Manufactured by : Pedders Shock Absorber Service Pty Ltd
Typical VIN : MMU148LH0DH675020
Seating Capacity : 2; 5
GVM : 3.3 tonne TO 3.3 tonne
Schedule 3
Expiry date : Life of Model
Plate location : 28 I 17
Plate colour : SILVER
Umesh Shamdasani
Associate Administrator of Vehicle Standards
28 August 2015
Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.
Approval No.: 45672 Issue Date: 28 August 2015
Schedule 4
ADR Document Reference from evidence item
01/00 COL2WD0100-1
02/01 COL2WD0201-1
03/03 COL2WD0303-1
04/05 COL2WD0405-1
05/05 COL2WD0505-1
06/00 COL2WD0600-1
08/01 COL2WD0801-1
11/00 COL2WD1100-1
13/00 COL2WD1300-1
14/02 COL2WD1402-1
18/03 COL2WD1803-1
23/02 (also satisfying 23/01) COL2WD2302-1
23/02 COL2WD2302-1
25/02 COL2WD2502-1
31/02 (using 35/03) SE3503RGCOL2
35/04 (also satisfying 31/02) SE3504RGCOL8
31/35SF SF3503RGCOL2
31/35SF SF3504RGCOL2
35/04 SE3504RGCOL8
35/04 (using 35/03) SE3503RGCOL2
42/04 COL2WD4204-1
43/04 COL2WD4304-1
46/00 COL2WD4600-1
47/00 COL2WD4700-1
48/00 COLRG2WD4800
49/00 COL2WD4900-1
50/00 COL2WD5000-1
51/00 COL2WD5100-1
61/02 COL2WD6102-1
62/02 COL2WD6202-1
79/03 RG2WDADR7903
81/02 COL2WD8102-1
83/00 COL2WD8300-1