Jenkins Springs Pty Ltd

PO Box 398

BASSENDEAN WA 6934

ATTENTION: Mr James McCully

 

Dear Mr McCully

The application for a Identification Plate Approval, your reference number CAWCS8G05, our reference number 47898, lodged for Jenkins Springs Pty Ltd, has been approved.

Your approval number is 47898 and the approval documents are attached.

Yours sincerely

Umesh Shamdasani

Associate Administrator of Vehicle Standards

28 June 2017

 

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Regional Development

MOTOR VEHICLE STANDARDS ACT 1989

Section 10A.(1) Approval

Approval No.: 47898

Issue date: 27 June 2017

The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.
  11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 47898 Issue Date: 27 June 2017

Schedule 1

Jenkins Springs Pty Ltd

188 Railway Parade

BASSENDEAN

WA 6054

 

Schedule 2

Make : WCS TOYOTA

Model : WCS TOYOTA HILUXGEN8

Category : NA

Manufactured by : Jenkins Springs Pty Ltd

Typical VIN : MR0KA3CB301234567

Seating Capacity : 2; 5

GVM : 3.3 tonne TO 3.5 tonne

 

Schedule 3

Expiry date : Life of Model

Plate location : PASSENGER SIDE B PILLAR

Plate colour : SILVER

Umesh Shamdasani

Associate Administrator of Vehicle Standards

27 June 2017

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 47898 Issue Date: 27 June 2017

Schedule 4

ADR Document Reference from evidence item

01/00 0100WCS8G

02/01 0200WCS8G

03/03 0303WCS8G

04/05 0405WCS8G

05/05 0505WCS8G

06/00 0600WCS8G

08/01 0801WCS8G

10/02 (also satisfying 10/01) 1002WCS8G

10/02 1002WCS8G

11/00 1100WCS8G

13/00 1300WCS8G

14/02 1402WCS8G

18/03 1803WCS8G

23/02 (also satisfying 23/01) 2302WCS8G

23/02 2302WCS8G

25/02 2502WCS8G

31/03 3103WCS8G

35/05 (also satisfying 31/03) 3505WCS8G03

31/35SF 31SFWCS8G03

35/05 3505WCS8G03

31/03 (also satisfying 35/05) 3103WCS8G

42/04 4204WCS8G03

43/04 4304WCS8G

46/00 4600WCS8G

47/00 4700WCS8G

48/00 4800WCS8G

49/00 4900WCS8G

51/00 5100WCS8G

61/02 6102WCS8G01

69/00 6900WCS8G

79/04 7904WCS8G02

81/02 8102WCS8G03

83/00 8300WCS8G

Approval No.: 47898 Issue Date: 27 June 2017

Schedule 5

 

1. This approval is for second-stage-of-manufacture WCS TOYOTA /WCS TOYOTA HILUXGEN8 based on first-stage Approval No. 47341 TOYOTA/ HILUX 8GEN issued on 10 July 2015.

2. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:

 

Niddrie Nameplates Pty Ltd

P.O. Box 106

Niddrie

VIC 3042

Phone : (03) 9335 2977