Pedders Shock Absorber Service Pty Ltd
PO Box 247
NOBLE PARK VIC 3174
ATTENTION:
Mr David Schneiders
Dear Mr Schneiders
The application for a Identification Plate Approval, your reference number NADMAXCA2, our reference number 47361, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.
Your approval number is 47361 and the approval documents are attached.
Yours sincerely
Martin Handley
Associate Administrator of Vehicle Standards
29 January 2016
GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/
Department of Infrastructure and Regional Development
MOTOR VEHICLE STANDARDS ACT 1989
Section 10A.(1) Approval
Approval No.: 47361
Issue date: 29 January 2016
The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).
In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.
The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.
This approval is subject to the following conditions.
Approval No.: 47361 Issue Date: 29 January 2016
Schedule 1
Pedders Shock Absorber Service Pty Ltd
6 Bridge Road
KEYSBOROUGH
VIC 3173
Schedule 2
Make : PEDDERS ISUZU
Model : D MAX
Category : NA
Manufactured by : Pedders Shock Absorber Service Pty Ltd
Typical VIN : MMU148MH0DH681726
Seating Capacity : 2; 4; 5
GVM : 3.45 tonne TO 3.45 tonne
Schedule 3
Expiry date : Life of Model
Plate location : 9 L 4
Plate colour : SILVER
Martin Handley
Associate Administrator of Vehicle Standards
29 January 2016
Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.
Approval No.: 47361 Issue Date: 29 January 2016
Schedule 4
ADR Document Reference from evidence item
01/00 NADMAX0100
02/01 NADMAX0201
03/03 NADMAX0303
04/05 NADMAX0405
05/05 NADMAX0505
06/00 NADMAX0600
08/01 NADMAX0801
11/00 NADMAX1100
13/00 NADMAX1300
14/02 NADMAX1402
18/03 NADMAX1803
23/02 (also satisfying 23/01) NADMAX23021
23/02 NADMAX23021
25/02 NADMAX2502
30/01 NADMAX3001
35/04 (also satisfying 31/02) NADMAX3504
35/04 (also satisfying 31/02) NADMAX35042
31/35SF NADMAXSF31-1
31/35SF NADMAXSF31-2
31/35SF NADMAXSF31-4
31/35SF NADMAXSF31-5
35/04 NADMAX3504
35/04 NADMAX35042
42/04 NADMAX4204
43/04 NADMAX4304
46/00 NADMAX4600-1
47/00 NADMAX4700
48/00 NADMAX4800
49/00 NADMAX4900
50/00 NADMAX5000-1
51/00 NADMAX5100
61/02 NADMAX6102
81/02 NADMAX8102
83/00 NADMAX8300
Approval No.: 47361 Issue Date: 29 January 2016
Schedule 5
1. The 'chassis-cab' variants of the PEDDERS ISUZU D-MAX vehicle type do not comply with the position requirements of ADR13/00 for the following lamps and reflectors:
- reversing lamps
- rear direction indicator lamps
- rear reflex reflectors
- rear registration plate lamps
- rear position (side) lamps
- stop lamps
2. The 'chassis-cab' variants of the PEDDERS ISUZU D-MAX vehicle type do not comply with:
- clause 14.2 of ADR42/04 for wheel guards on the rearmost wheels.
- clause 9.1.1.1 of ADR61/02 for provision of a rear registration plate.
3. The manufacturer must provide instructions, guidelines and references to the relevant ADRs, that must be met, to whoever is responsible for completing chassis-cab vehicles certified in accordance with Circular 0-4-11 prior to their supply to the market.
4. This approval is for second-stage-of-manufacture PEDDERS ISUZU D-MAX based on first-stage Approval No. 43971 ISUZU D-MAX issued on 2 Feburary 2012.
5. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:
Niddrie Nameplates Pty Ltd
P.O. Box 106
Niddrie
VIC 3042
Phone: (03) 9335 2977
Facsimile: (03) 9335 4357