Pedders Shock Absorber Service Pty Ltd

PO Box 247

NOBLE PARK VIC 3174

ATTENTION: Mr David Schneiders

 

Dear Mr Schneiders

The application for a Identification Plate Approval, your reference number NA200CA, our reference number 46509, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.

Your approval number is 46509 and the approval documents are attached.

Yours sincerely

 

Umesh Shamdasani

Associate Administrator of Vehicle Standards

30 January 2015

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Regional Development

MOTOR VEHICLE STANDARDS ACT 1989

Section 10A.(1) Approval

Approval No.: 46509

Issue date: 30 January 2015

The Administrator of Vehicle Standards (the Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.
  11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 46509 Issue Date: 30 January 2015

Schedule 1

Pedders Shock Absorber Service Pty Ltd

6 Bridge Road

KEYSBOROUGH

VIC 3173

 

Schedule 2

Make : Pedders Toyota

Model : Landcruiser NA 200

Category : NA

Manufactured by : Pedders Shock Absorber Service Pty Ltd

Typical VIN : JTMHV05J804103407

Seating Capacity : 5

GVM : 3.5 tonne TO 3.5 tonne

 

Schedule 3

Expiry date : Life of Model

Plate location : 10 M 22

Plate colour : SILVER

Umesh Shamdasani

Associate Administrator of Vehicle Standards

30 January 2015

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 46509 Issue Date: 30 January 2015

Schedule 4

ADR Document Reference from evidence item

01/00 NA2000100

02/01 NA2000201

03/03 NA2000303

05/05 NA2000505

06/00 NA2000600

08/01 NA2000801

11/00 NA2001100

13/00 NA2001300

14/02 NA2001402

18/03 NA2001803

23/02 (also satisfying 23/01) NA2002302

23/02 NA2002302

25/02 NA2002502

30/01 NA2003001

35/04 (also satisfying 31/02) NA2003504SE3

31/35SF NA200SF3503

35/04 NA2003504SE3

42/04 NA2004204

42/04 NA20042041

43/04 NA2004304

46/00 NA2004600

47/00 NA2004700

48/00 NA2004800

49/00 NA2004900

50/00 NA2005000

51/00 NA2005100

61/02 NA2006102

62/02 NA2006202

69/00 NA200690001

72/00 NA200ADR7200

81/02 NA2008102

83/00 NA2008300

Approval No.: 46509 Issue Date: 30 January 2015

Schedule 5

 

1. This approval is for second-stage-of-manufacture Pedders Toyota Landcruiser NA 200 based on first-stage Approval No. 43656 Toyota Landcruiser 200 Comm issued on 31 August 2011.

2. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:

Niddrie Nameplates Pty Ltd

P.O. Box 106

Niddrie

VIC 3042

Phone: (03) 9335 2977

Facsimile: (03) 9335 4357